H
H
2
2
0
0
-
-
8
8
5
5
0
0
1
1
L
L
I
I
Q
Q
U
U
I
I
D
D
C
C
O
O
O
O
L
L
I
I
N
N
G
G
K
K
I
I
T
T
TUTORIAL & INSTALLATION GUIDE
These instructions are also available with color pictures on our web site at
http://www.swiftnets.com/Products/installation_guide_h20-8501.pdf
Check-marked for applicable model and content
Intel Pentium 3 Socket 370, AMD Duron, Athlon, MP, XP socket 462
Intel Xeon Processor, socket 603/604
Intel Pentium 4 socket 478
Bare kit without water-block
AMD Athlon 64 & Opteron
Qty Item Incl. Qty Item Incl.
1
MCW5000-A CPU water-block, with retention
hardware
2 Springs 0.375 OD x 1” long
D
1
MCW5000-P CPU water-block, with retention
hardware
1
FBK525 assy. incl. (1) ½” fill & bleed kit, (2) 7/32-5/8”
worm drive hose clamps
D
1
MCW5000-PX CPU water-block to use with
Intel validated retention hardware provided
with your CPU or motherboard.
2 2 ½ ft long ½” OD vinyl tubes for fill and bleed operations
D
1
MCW5000-64 CPU water-block, with
retention hardware
1
MCP600 12 Volts DC industrial pump with retention
screws
D
1 MCR80-F1 radiator assy. incl. (1) Radiator, (1)
80x80x25mm fan, (1) fan guard, (4) #6 x 1 ¼”
screws, (4) #6 x 3/8” screws, (2) 7/32-5/8”
worm drive hose clamps
D
7 Feet ½” OD high quality vinyl tubing
D
1 1ft of ½” tube ID thick wall Clearflex tubing, (2)
½” to 3/8” barb nylon adapters
D
1
2 oz bottle HydrX specially formulated coolant
D
Table of contents
1. Tube routing
2. Installation of the cooling components
3. Fill-and-bleed operations
4. Draining the system
5. Optional accessories
6. Disclosures & warranty information
……………………………………………………………………………………
……………………………………………………………………………………
……………………………………………………………………………………
……………………………………………………………………………………
……………………………………………………………………………………
……………………………………………………………………………………
Page 2
Pages 3-4
Pages 5,6,7
Page 7
Page 8
Page 8
Preamble
This kit has been designed to facilitate installation of the components with no modifications required to the chassis. It is however meant for advanced
users, well versed in installing computer components.
General guidelines
Never work with electricity connected to the computer while work is in progress.
The fill and bleed kit should always be at the highest point of the cooling circuit (top 5 ¼” tray)
While it is possible to install the kit in a chassis already populated with all typical components, such as hard drive, CD Rom, power supply, etc, it
is always preferable and easier to work on a “naked” case, removing both side panels, front bezel, and top panel.
Rouchon Industries, Inc., dbA Swiftech – 1703 E. 28
th
St, signal Hill, CA 90755, USA – T (562) 595-8009 – F (562) 595-8769 – All content Copyright
Swiftech 2004 – Last edited 1-24-04– Subject to revision without notice - 1 -
Kommentare zu diesen Handbüchern