Swiftech MCW5002 64 Bedienungsanleitung PDF herunterladen

Swiftech Inc., 1703 E. 28

St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769

Parts list

Parts QTY PARTS QTY

MCW5000-64™ assembly 1 Aluminum tension limiter 2

6-32 x 1 ¾ Philips screw 2 Springs 2

Nylon shoulder washers 2 Arctic Alumina Thermal compound 1

Tube inserts 4 Nylon spacers 2

This product is intended for expert users. Please consult with a qualified technician for installation. Improper installation may result in

damage to your components. Swiftech assumes no liability whatsoever, expressed or implied, for the use of these products, nor their

installation. The following instructions are subject to change without notice. Please visit our web site at www.swiftnets.com

for

updates.

1. Before you install the MCW5000-64™ water-block:

a. Prepare two pieces of tubing of sufficient length to connect

to the rest of your circuit. The cuts must be square as shown in

figure 1 or leaks may occur:

b. Install the provided plastic tube inserts at each end of the tubes,

as shown in figure 2: these inserts are absolutely imperative when

using any kind of soft tubing, such as vynil, ClearFlex, Taigon, etc...

Square cut

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

c. Spread a little bit of grease or simple

liquid soap around the tubing. It helps pushing

the tubes in, particularly with Clearflex tubing,

which features a very “sticky” surface.

d. Fully insert both tubes into the fittings. The tip of the plastic tube inserts should

be flush with the inlet and outlet openings, as shown in figure 4 above. Inserting the

tubes requires a firm push, accompanied by a twisting motion.

2. Preparing your Motherboard

 Remove the existing heat sink

 Carefully clean the CPU.

 Lightly coat the CPU with the provided thermal compound. Only a paper-thin coat is necessary. It should be applied

using preferably a razor blade, or a credit card, held between thumb and index at a 45-degree angle.

3. MCW5000-64™ water-block installation diagram

 Method 1: The MCW5000-64 water-block bolts onto AMD’s validated plastic retention frame with two screw

spring assemblies. Please use the retention frame provided by your motherboard vendor. Remove the two

existing screws that hold the frame in place, place the water-block assembly onto the CPU, and use these two

holes to bolt down the spring assemblies, as shown in figure 6, page 2. Each spring assembly features an

aluminum spacer acting as a tension limiter. It’s main purpose is to guarantee that each springs is compressed

to the exact same amount of tension (35lbs each).

 Method 2: It is also possible to install the MCW5000-64 without the stock plastic retention frame.

However, you MUST then use the nylon spacers provided with your accessories package as shown in figure 7,

page 2. These are necessary to replace the stock plastic retention frame and to provide support to the entire

assembly.

Page 1 of 2

1 2

Parts list 1

Inhaltsverzeichnis

Seite 1 - Parts list

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769 Parts list Parts QTY PARTS QTY MCW5000-64™ assembly 1

Seite 2

Installation with stock plastic retention frame 6x32 philips screwNylon shoulder washerSpringAluminumtension limiterSocketSocketPlastic retentionfram

Kommentare zu diesen Handbüchern

Keine Kommentare

Swiftech MCW5002 64 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Computerzubehör Swiftech MCW5002 64 herunter. Swiftech MCW5002 64 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Computerzubehör Swiftech MCW5002 64