Swiftech MCW5000 PT Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Computerzubehör Swiftech MCW5000 PT herunter. Swiftech MCW5000 PT User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 4
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
Swiftech Inc., 1703 E. 28
th
St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769
Page 1 of 4
Parts list
Parts QTY PARTS QTY
Water-block, with TEC & gaskets assy. 1 Arctic Alumina Thermal compound 1
Tube inserts 4 Hex L-key 1
Tube removal tool 1 Euro-style connector 1
Motherboard installation hardware pack 1
This product is intended for expert users only. Please consult with a qualified technician for installation. Improper installation may result in
damage to your components.
Swiftech assumes no liability whatsoever, expressed or implied, for the use of these
products, nor their installation.
The following instructions are subject to change without notice. Please visit our web site at
www.swiftnets.com
for updates
1. Before you install the MCW5000-PT water-block:
Prepare two pieces of tubing of sufficient length to connect to
the rest of your circuit. It is preferable to insert the tubing into the
block BEFORE it gets installed onto the CPU, to prevent placing
undue pressure onto the assembly when it is installed on the
CPU.
The cuts to the tubing must be square as shown in figure 1 or
leaks may occur. Use a good pair of scissors to cut the tubing. It
is easier than with a razor blade.
Square cut
Figure 1
Install the provided plastic tube inserts at each end of the tubes, as
shown in figure 2: these inserts are absolutely imperative when using
any kind of soft tubing, such as vynil, ClearFlex, Taigon, etc...
Figure 2
Figure 3
Figure 4
Figure5
c. Spread a little bit of grease (Vaseline etc..) around the
tubing. It helps pushing the tubes into the fittings.
d. Fully insert both tubes into the fittings. The tip of the plastic tube
inserts should be flush with the inlet and outlet openings, as shown in figure
4 above. Inserting the tubes requires a firm push, accompanied by a twisting
motion.
Seitenansicht 0
1 2 3 4

Inhaltsverzeichnis

Seite 1 - Parts list

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769 Page 1 of 4 Parts list Parts QTY PARTS QTY Water-blo

Seite 2 - Swiftech Inc., 1703 E. 28

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769 Page 2 of 4 2. Preparing the motherboard Install the

Seite 3

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769 Page 3 of 4 Remove the peel-off paper back from the mot

Seite 4

Swiftech Inc., 1703 E. 28th St., Signal Hill, CA 90755 T. (562) 595-8009 F. (562) 595-8769 Page 4 of 4 Now, you can re-install the MB inside the c

Kommentare zu diesen Handbüchern

Keine Kommentare